Raw Read Error Rate Fail
We shall see how this turns out. Maybe it's not that bad? Maybe its a problem from SMART? You should post your syslog, or even better, generate and post your diagnostics file. Check This Out
However it was stuck at the memory testing - long before it actually checked to see if drives existed. A raw read error is triggered when the drive detects that it read bad data. How to reset HDD S.M.A.R.T? That is is just mind shatteringly insane !
How To Fix Raw Read Error Rate
And if you have exhausted all connection related ideas and that value still increases then i would contact tech support and TELL them you want a new drive because this is The value is just an indicator, changing it won't make it work any better. If we assume a linear relationship, then it would appear that each point represents approximately 4000 counts. If reading a sector fails, it becomes pending.
SMART status says Raw Read Error Rate: Current value 4 (note: earlier today this value was 1), Threshold 6, Raw Value 0, Worst 1, Status FAILED. That said, the initial warning, if it came from BIOS or the OS, would suggest that the drive should be replaced, or at least relegated to storing non-critical data. xkm121 2012-12-31 01:54:45 UTC #7 I checked my Event view log, I cannot see any warning messages concerning I/O transfer. And the RRE value just went over 122. Raw Read Error Rate Western Digital Fix LinkBack Thread Tools Display Modes #1 (permalink) June 30, 2012, 08:56 AM Zaqueo Rookie Join Date: Jun 2012 Posts: 4 [S.M.A.R.T.] Raw Read Error Rate Failed?
Message 11 of 12 (164 Views) Reply 0 Thanks Mav Moderator Posts: 12,769 Thanks: 376 Fixes: 50 Registered: 06-04-2007 Re: Raw Read Error Rate failure 09-12-2013 10:59 AM Options Mark as What Is Raw Read Error Rate Are WD's engineers not aware that Seagate's and WD's SMART attributes are completely different? maybe take a close look at the connectors on the motherboard to so you can make sure they don't have dust or whatever on them.. Status OK Disk information firmware M306 temp 31C Total host reads: 4.4 TB Total host writes: 1.6 TB This SSD was purchased in July 2013.
What Is Raw Read Error Rate
The Current pending sectors count of 8 may in fact represent 8 logical sectors which would correspond to a single physical sector in an Advanced Format drive. The Reported Uncorrectable Errors are of concern, too. How To Fix Raw Read Error Rate Lastly about the event viewer.. Raw Read Error Rate Western Digital C8 Write Error Count 0 OK 200 155 51 N.A.
BB (Unknown attribute) 0 OK 100 100 0 N.A. his comment is here I will take his word for now. So a 114 in read/error rates is better than 113. I have no idea how to interpret the ATTO results nor the SMART status. How To Fix Raw Read Error Rate Samsung
HDTune info: Code: HD Tune: SAMSUNG SP1604N Health ID Current Worst ThresholdData Status (01) Raw Read Error Rate 100 100 51 1 Ok (03) Spin Up Time 100 100 25 4544 fast forward, modern drives (not drivers) , or Winchesters as we once called them have error correction, from DAy1, EVEN DAY 1 , SECTORS are bad.! (fact) so they , map Then Hitachi's technical database will probably vanish from the Internet. this contact form Powered through an APC RS 1200G .
However, subsequent (2 power cuts already today, before 8am, and several over the previous days) have not shown any further error reports, although, as I said, the attribute raw value is
Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the Something is not right. Hmm? Raw Read Error Rate Meaning C9 Off Track Errors 0 OK 253 252 0 N.A.
thanks a lot here is the drive info: Code: Device ID: 0 Device Capacity: 6194253374051377 MB Serial Number: 1191J1FA124831 Model Number: SAMSUNG SP1604N Firmware Revision: TM100-31 Partitions: C: 20481 MB D: Imagine if Intel shipped CPU's with a failure rate that high and then a failure rate of the RMA refurb products too.. If you could return it for an exchange, that is a very different prospect.I tend to agree. navigate here C7 UltraDMA CRC Error Count 0 OK 199 199 0 N.A.
BD (Unknown attribute) 0 OK 100 100 0 N.A. How to reset Western Digital hard disk S.M.A.R.T? and yeah if i was in your shoes i would choked too so sorry to hear about your problems.. WD10EARS 2012-12-31 20:28:50 UTC #8 I posted my benchmark picture in here already a few weeks ago i think it was.
there is no perfect HDD, never was, never will be, (history and fact) in the olden days, (me) we had to enter the bad sectors in to the HDD controller from In BIOS SATA set as AHCI WD Black 2TB 2002FAEX-007BA0 Radeon 5870 GSkill DDR2-1066 8GB Windows 7 Professional SP1 with all patches All Intel Drivers, including the Instel Rapid Storage Technology and i too had my drive for the same amount of time and it rapidly got worse real fast.. When to use "ĉu" instead of "se"?
which is why i waited so long to do something about it.. Auto Offline data collection on/off support. I have seen somewhere that people claim these drives have a 33% failure rate. You could replace whatever components have failed (best case that'd mean soldering new components to the control board on the bottom of the drive), but that's not really practical.
about how that *should be a warranty smart setting. Powered through an APC RS 1200G .